Brain / iKon / Xbar / TracX by MSH Electronics Srl (Universal)
(24)
Released: Nov 18, 2015
Version: 3.3.039
Size: 118 MB
Deal Alert
Get notified when this app is on sale or goes free [privacy policy]

Price History

Ranking - Entertainment (iPhone)

Ranking - Entertainment (iPad)

Brain / iKon / Xbar / TracX

MSH Electronics Srl
Screenshot #1 (iPhone)
App for iOS tablets and phones. It allows to set parameters and settings on Brain/Ikon/Xbar/Tracx flybarless controllers via Bluetooth.

App is supported natively by MSH Flybarless units with integrated Bluetooth, all other units type need an external MSH Bluetooth dongle for iOS, sold separately.

This App needs latest firmware release on the unit to be used to its full potential. If your devices has internet access, the app will prompt you in case a new firmware for the flybarless unit is available.

MSH products can be purchased in any of the official MSH dealer shop.

What's new in version 3.3.039
• Introduced the possibility to control Tandem Rotors models such as the Vario Chinook
• Added the possibility to log RPM also from a second electric motor (EG: model with tail motor or model with two motors like Velos)
• Added the possibility to read and record in the Flight Logs the value of a PWM signal output from an external device
• Added the possibility to control through an additional radio channel assigned to the new B-Aux3 function, a PWM signal output on the CH4 connector to control an additional function in addition to the B-Aux2 one already present on the CH2 connector. To disable PWM Output set B-Aux3 to “No Channel”
• Now even with standard receivers with separate channels wires, the QOS values of the received signal are calculated and therefore also with these receivers the parameters "RxFrameRate mS", RxFades n°", Frame Losses n°", Holds n°" can be recorded in the flight logs memory
• Added to the loggable parameters “Global Vibrations” value
• Added to telemetric parameters manageable via Jeti telemetry “Global Vibrations”
• Added to telemetric parameters manageable via Spektrum telemetry “Global Vibrations” under the emulated sensor “Fuel Status”. “Fuel Consumed” is the instantaneous value of “Global Vibrations” for which the alarm can be set, “Flow Rate” is the maximum value of “Global Values” reached during flight
• Added to telemetric parameters manageable via S.Port (OpenTX) telemetry “Global Vibrations” under the emulated sensor “Fuel”
• Added to telemetric parameters manageable via F.Port (OpenTX) telemetry “Global Vibrations” under the emulated sensor “Fuel”
• Added for diagnostic purpose to the loggable parameters “CPU Temperature C°”. This value is also now visible on the top bar of channels panels at the right of “(servo voltage = x,x V)”
• Added the two new events “Check Mode Activated” & “Check Mode Disactivated”. This let know to some user why during setup Throttle do not work and why green led go to off
• Added the new event “Loaded a Configuration File”
• Now telemetry values are read also from old Platinum V3 ESC’s. Only RPM & Power Output (PWM). If ESC governor is used, Power Output can be very useful to verify that the used gear ratio is correct
• Added the new loggable parameter "ExtRxVoltage" which is the voltage read by the auxiliary connector ("extra voltage") available on some Futaba receivers (already telemetrically transmitted on the RX slot 0)
• Now with SPM4649T receivers the voltage seen on “Telemetry” page of TX for “Volts” sensor is that read from the “V Batt” connector of the 4649T RX (in the “Flight Log” page the voltage reported for “Receiver” continue to be the Servo Voltage of Brain2 as before)
• Now Fades calculations work with SRXL2 protocol also with DX6 or DX7 Gen2 EU version transmitters working only at 22ms (it is required a new 4651T firmware that responds as required by the protocol, to the bind status interrogation)
• Revised the range of Fine tuning by dials / potentiometers / Trim increasing PID range for tail, aileron and elevator with some update of the min and max values
• For those who, after setup, use pitch curves with reduced negative values (reproductions, some beginners, etc.), the storage of dials values are now also performed with collective pitch values between -100% and zero
• Eliminated repetitions of EVENTS when the motor fast start of Autorotation Bailout is running
• Revised for F.Port the “Frame Rate” calculation due to the different frame rate in ACCST mode (9ms) and in the new ACCESS mode (7ms)
• Eliminated the annoying false alarms generated with SRXL2 receivers if during setup with a USB powered control unit the power is removed and restored to the receiver and servos
• When in demo mode, if a configuration file is loaded, the type of control unit from which the file has been saved is recognized and the correct scheme for that type of unit is displayed
[MORE]
Our verdict: Meh!
  • Brain / iKon / Xbar / TracX is a poorly rated app (2.5-star).
Similar Apps
Talking Tom Cat

iPhone App - Designed for iPhone, compatible with iPad

Developer: Outfit7 Limited || Version: 3.9

Crunchyroll

Universal App - Designed for iPhone and iPad

Developer: Ellation, Inc. || Version: 4.8.0

Ghost Hunter M2

iPhone App - Designed for iPhone, compatible with iPad

Developer: Michael Weber || Version: 8.2.3